| Deposit | Description | 4 Hours | Daily | Weekly | Monthly | |||
| AUTOMOTIVE TOOLS (GENERAL) | ||||||||
| 160 | Engine Hoist w/sling (1200 lb.) | 30 | 40 | 160 | 420 | |||
| 60 | Low lift Post for vans | 10 | 20 | 60 | 180 | |||
| 20 | Adjustable Sling | 3 | 5 | 15 | 45 | |||
| 60 | Floor Jack | -- | 20 | 60 | 180 | |||
| (2 ¼ ton, 19 ½” height) | ||||||||
| 30 | Jack Stands (1 pair) | -- | 10 | 30 | 60 | |||
| MISCELLANEOUS TOOLS | ||||||||
| 25 | Small Rivet Gun (up to 3/16”) | -- | 6 | 18 | 50 | |||
| 60 | Big Rivet Gun (1/8” - ¼”) | 10 | 12 | 36 | 100 | |||
| 30 | Double Flaring Tool (double flare) | 6 | 8 | 16 | 32 | |||
| 20 | Bearing & Race & Seal Driver | -- | 6 | 12 | 36 | |||
| (Set of 11) | ||||||||
| 20 | Extractor #6 or#7 | -- | 5 | 15 | 30 | |||
| 20 | Steering Wheel Puller (187) | -- | 5 | 15 | 30 | |||
| 20 | Pivot Pin Remover (KM21854-01) | -- | 5 | 15 | 30 | |||
| 30 | HD Snap Ring Pliers | -- | 8 | 24 | 48 | |||
| w/6 pairs of ends | ||||||||
| 30 | Ford Fan Clutch Wrench Set (3296) | -- | 10 | 30 | 90 | |||
| 30 | Cylinder Leak Down Tester | -- | 10 | 30 | 90 | |||
| WRENCHES & SOCKETS | ||||||||
| 100 | ½” Impact Wrench | 10 | 15 | 60 | 180 | |||
| Electric - 217 ft. lbs. | ||||||||
| 50 | ½” Impact Wrench | -- | 12 | 48 | 130 | |||
| Air - 500 ft. lbs. | ||||||||
| 100 | ¾” Impact Wrench | 14 | 20 | 80 | 320 | |||
| Air – 900 ft. lbs. | ||||||||
| 40 | 3/8” Torque Wrench (250 inch/lb) | -- | 8 | 24 | 75 | |||
| 40 | ½” Torque Wrench (150 feet/lb) | -- | 8 | 24 | 75 | |||
| 60 | ¾” Torque Wrench (300 feet/lb) | -- | 18 | 36 | 108 | |||
| 40 | ¾” Ratchet or ¾” Breaker Bar | -- | 6 | 18 | 36 | |||
| 10 | ½” or ¾” Standard Sockets (each) | -- | 3 | 9 | 18 | |||
| 15 | ½” or ¾” Deep Sockets (each) | -- | 4 | 12 | 24 | |||
| 20 | ½” - ¾” or ¾” - ½” Adapters | -- | 2 | 4 | 8 | |||
| 15 | ½” Deep Metric Sockets | -- | 4 | 12 | 24 | |||
| (30, 32, 34, 36mm) | ||||||||
| 20 | Ball Joint Sockets | -- | 5 | 15 | 45 | |||
| (2 1/8”, 1 29/32”) | ||||||||
| 20 | Chain Wrench ½”- 4 ¾” (7400) | -- | 5 | 15 | 30 | |||
| 20 | Universal Oxygen Sensor Socket | -- | 4 | 12 | 24 | |||
| PULLERS & INSTALLERS | ||||||||
| 40 | U-Joint Press (CJ91C1) | -- | 8 | 24 | 48 | |||
| 40 | Serpentine Belt Tightening Tool | -- | 10 | 30 | 90 | |||
| 25 | Harmonic Balancer/Steering Wheel Puller (3041) | -- | 7 | 21 | 50 | |||
| 40 | Harmonic Balance Puller (97400) | -- | 12 | 36 | 72 | |||
| 20 | Harmonic Balancer Installer (188) | -- | 6 | 18 | 36 | |||
| 40 | Pilot Bearing Puller (193) | -- | 10 | 30 | 90 | |||
| 30 | P.S. Pump Pulley Replacer (7005) | -- | 5 | 15 | 45 | |||
| 30 | P.S. Pump/Alt. Pulley Remover (7185) | -- | 7 | 21 | 50 | |||
| 30 | Clutch Alignment Tool (6 pieces) | -- | 6 | 18 | 36 | |||
| 20 | 2-Jaw Puller (6”) | -- | 4 | 12 | 36 | |||
| 30 | 3-Jaw Puller (4”) | -- | 5 | 15 | 30 | |||
| 30 | 3-Jaw Puller (6”) | -- | 6 | 18 | 36 | |||
| 40 | 3-Jaw Puller (8”) | -- | 7 | 21 | 42 | |||
| 40 | 2-Jaw/10 Ton Puller (4 ½” or 7” leg) | -- | 8 | 24 | 48 | |||
| 40 | Large Gear and Pulley Puller (S22) | -- | 10 | 30 | 60 | |||
| 20 | Bearing Splitter (up to 2 ¼”) - 251 | -- | 4 | 12 | 24 | |||
| 40 | Slide Hammer Puller Kit | -- | 10 | 30 | 90 | |||
| 50 | Slide Hammer Puller w/Axle Bearing Puller | -- | 14 | 42 | 126 | |||
| 40 | Pulley and Bearing Puller (J4053) | -- | 6 | 18 | 36 | |||
| FRONT END TOOLS | ||||||||
| 15 | Ball Joint Separator (fork 26) | -- | 4 | 12 | 36 | |||
| 50 | Ball Joint Press (OW7249) | -- | 12 | 30 | 60 | |||
| 30 | Ball Joint Adapters (for trucks) | -- | 5 | 15 | 45 | |||
| 20 | Tie Rod End Separator | -- | 5 | 15 | 45 | |||
| (1 3/8”, 1” , 11/16”) | ||||||||
| 50 | Universal Tie Rod End Puller (7315A) | -- | 9 | 27 | 83 | |||
| 40 | Inner Tie Rod End Tool (45750) | -- | 10 | 30 | 90 | |||
| 20 | Pittman Arm Puller (Small – for cars) | -- | 4 | 12 | 36 | |||
| 30 | Pittman Arm Puller (Large – for trucks) | -- | 8 | 24 | 48 | |||
| 50 | Inner CV Joint Puller (7507) | -- | 10 | 30 | 90 | |||
| w/Slide Hammer Puller | ||||||||
| 40 | Slide Hammer Puller (1179) | -- | 10 | 30 | 60 | |||
| 60 | Universal Hub Puller (OTC 7394) | -- | 12 | 36 | 72 | |||
| 30 | Hub Puller/Flange Axle Yoke (499Z) | -- | 6 | 12 | 36 | |||
| 30 | Front Hub Installer (7135) | -- | 6 | 12 | 36 | |||
| 100 | Strut Spring Compressor (7560) clamshell | -- | 15 | 45 | 100 | |||
| 100 | Strut Spring Compressor (7294) spring/hook | -- | 10 | 30 | 60 | |||
| 20 | Ball Joint Sockets | -- | 5 | 15 | 45 | |||
| (2 1/8” - 1 29/32”) | ||||||||
| 25 | Wheel Bearing Locknut Wrenches | -- | 6 | 12 | 36 | |||
| 10 | Disc Brake Pad Spreader (LS24400) | -- | 3 | 9 | 27 | |||
| AIR CONDITIONING SERVICE TOOLS | ||||||||
| 15 | Clutch Plate Holder (universal) | -- | 4 | 12 | 36 | |||
| 20 | Clutch Plate Remover (all brands) | -- | 6 | 18 | 36 | |||
| 20 | Clutch Plate Installer (all brands) | -- | 6 | 18 | 36 | |||
| ENGINE BUILDING TOOLS | ||||||||
| 50 | H.D. Double Spiral Cylinder Flex Hone | -- | 10 | 40 | 120 | |||
| (BRGB - up to 4 1/8” / BRGB 3 ½”) | ||||||||
| 20 | Piston Ring Compressor (2 1/8” - 5” band) | -- | 4 | 12 | 36 | |||
| 40 | Piston Ring Pliers & Ring Expander Sets | -- | 10 | 30 | 90 | |||
| 15 | GM Valve Spring Compressor | -- | 3 | 12 | 36 | |||
| 30 | Valve Spring Compressor | -- | 5 | 10 | 30 | |||
| 25 | Universal Valve Spring Compressor (CF811) | -- | 8 | 16 | 38 | |||
| 60 | Overhead Valve Spring Compressor (KD3087) | -- | 10 | 40 | 120 | |||
| 20 | Ridge Reamer 3” - 5” (LS38000) | -- | 5 | 10 | 30 | |||
| 60 | Overhead Valve Spring Compressor (59550) | -- | 10 | 40 | 120 | |||
| for deep recessed valves | ||||||||
| 11 | ||||||||